ubuntu下smokeping安装配置

#sudo vim /etc/network/interfaces 

auto eth0
iface eth0 inet dhcp

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
auto eth0
#iface eth0 inet dhcp

iface eth0 inet static
address 10.138.16.245
netmask 255.255.255.240
gateway 10.138.16.254

sudo /etc/init.d/networking restart

sudo aptitude install rrdtool apache2 fping echoping libapache2-mod-speedycgi libwww-perl libsocket6-perl libnet-telnet-perl libnet-dns-perl libnet-ldap-perl libio-socket-ssl-perl libauthen-radius-perl libcgi-perl librrds-perl librrdp-perl

sudo apt-get install smokeping curl libauthen-radius-perl libnet-ldap-perl libnet-dns-perl libio-socket-ssl-perl libnet-telnet-perl libsocket6-perl libio-socket-inet6-perl apache2

sudo apt-get install smokeping

sudo apt-get install sendmail

#sudo vim /etc/smokeping/config.d/Presentation

sudo apt-get install ttf-wqy-zenhei

enadmin@BJCGNMON01:/etc/smokeping/config.d$ sudo find / -name Graphs.pm
[sudo] password for enadmin: 
/home/enadmin/Graphs.pm
/usr/share/perl5/Smokeping/Graphs.pm

 if ($mode =~ /[anc]/){
        my $val = 0;
        for my $host (@hosts){
            my ($graphret,$xs,$ys) = RRDs::graph
            ("dummy",
            '--start', $tasks[0][1],
            '--end', $tasks[0][2],
            '--font TITLE:20:"WenQuanYi Zen Hei Mono"',
            "DEF:maxping=$cfg->{General}{datadir}${host}.rrd:median:AVERAGE",
            'PRINT:maxping:MAX:%le' );
            my $ERROR = RRDs::error();
            return "<div>RRDtool did not understand your input: $ERROR.</div>" if $ERROR;
            $val = $graphret->[0] if $val < $graphret->[0];
        }
        $val = 1e-6 if $val =~ /nan/i;
        $max = { $tasks[0][1] => $val * 1.5 };
    }

sudo find / -name Graphs.pm

sudo vim /etc/smokeping/config.d/Targets

+ Gansu //注意，这里加号后面的必须是英文，不能是中文
menu = 甘肃
title = 甘肃

++ Daliang //同样，这里‘++’后面的必须是英文，+和++后面的内容是不会被现实的，只是起一个命名的作用。
menu =大梁
title =大梁:10.138.1.11
host = 10.138.1.11
alerts = someloss

#sudo /etc/init.d/smokeping restart

+ yiji
menu = 一级
title = 一级

++ erji
menu = 二级
title = 二级

+++ sanji
menu = sanji
title =sanji:10.138.16.54
host = 10.138.16.54
alerts = someloss

*** Alerts ***
to = |/etc/smokeping/alert.sh
from = aaa@126.com

+someloss
type = loss
# in percent
pattern = >90%,*12*,>90%,*12*,>90%
edgetrigger = yes
comment = loss 3 times  in a row

+rttbad
type = rtt
# in milliseconds
pattern = ==S,>50,>50
edgetrigger = yes
comment = route


# This rule checks for 3 periods (3 * 5min default) where
# the rtt is >70ms
+rttdetect
type = rtt
# in milli seconds
pattern = >70,>70,>70
edgetrigger = yes
comment = On backup circuit maybe?

#!/bin/sh
echo "$2 got smokeping $1 from Monitor Server, The $2 IP is: $5........name-of-alert:$1, target:$2, loss-pattern:$3, rtt-pattern:$4, hostname:$5,[raise]:$6" |mutt -s "smokeping alert $2" xwdreamer@126.com

#如果在12次检查中出现了3次丢包的情况(不论丢多少个包)，就进行alert；
+someloss
type = loss
# in percent
pattern = >0%,*12*,>0%,*12*,>0%
comment = loss 3 times  in a row

#如果连续出现两次50毫秒以上的延时，就进行alert；
+rttbad
type = rtt
# in milliseconds
pattern = ==S,>50,>50
comment = route

#之前5次检查延时都少于10毫秒，前6次检查延时都少于100毫秒，第7次开始连续3次检查延时都大于100毫秒的话，就进行alert。
+rttdetect
type = rtt
# in milliseconds
pattern = <10,<10,<10,<10,<10,<100,>100,>100,>100
comment = routing messed up again ?