DHCP中继 NAT 让客户端自动获取ip地址并ping通外网！-阿里云开发者社区

DHCP中继 NAT 让客户端自动获取ip地址并ping通外网！

2017-11-07 1188

版权

本文内容由阿里云实名注册用户自发贡献，版权归原作者所有，阿里云开发者社区不拥有其著作权，亦不承担相应法律责任。具体规则请查看《阿里云开发者社区用户服务协议》和《阿里云开发者社区知识产权保护指引》。如果您发现本社区中有涉嫌抄袭的内容，填写侵权投诉表单进行举报，一经查实，本社区将立刻删除涉嫌侵权内容。

本文涉及的产品

公网NAT网关，每月750个小时 15CU

简介：

首先给给c1和c2 分vlan 在交换机R5上设置

R5>en
R5#conf t
R5(config)#vlan 10
R5(config-vlan)#vlan 20
R5(config-vlan)#inter fa1/1
R5(config-if)#switchport access vlan 10
R5(config-if)#inter fa1/2
R5(config-if)#switchport access vlan 20
R5(config-if)#inter fa1/0
R5(config-if)#switchport mode trunk
R5(config-if)#switchport trunk encapsulation d
R5(config-if)#switchport trunk encapsulation dot1q
然后设置DHCP地址池

dhcp>en
dhcp#conf t
dhcp(config)#ip dhcp p
dhcp(config)#ip dhcp pool
dhcp(config)#ip dhcp pool v10
dhcp(dhcp-config)#netw
dhcp(dhcp-config)#network 192.168.10.0 255.255.255.0
dhcp(dhcp-config)#de
dhcp(dhcp-config)#default-router 192.168.10.1
dhcp(dhcp-config)#ip dhcp pool v20
dhcp(dhcp-config)#default-router 192.168.20.1
dhcp(dhcp-config)#network 192.168.20.0 255.255.255.0
dhcp(dhcp-config)#inter fa0/0
dhcp(config-if)#ip add
dhcp(config-if)#ip address 192.168.100.100 255.255.255.0
dhcp(config-if)#no shut
dhcp(config-if)#end
dhcp(config)#ip route 0.0.0.0 0.0.0.0 192.168.100.10
dhcp(config)#do ping 192.168.100.10
Sending 5, 100-byte ICMP Echos to 192.168.100.10, timeout is 2 seconds:
.!!!!

然后设置DHCP中继在R3上配置！

R3>en
R3#conf t
R3(config)#vlan 10
R3(config-vlan)#vlan 20
R3(config-vlan)#inter vlan 10
R3(config-if)#ip address 192.168.10.1 255.255.255.0
R3(config-if)#ip helper-address 192.168.100.100
R3(config-if)#no shut
R3(config-if)#inter vlan 20
R3(config-if)#ip helper-address 192.168.100.100
R3(config-if)#ip address 192.168.20.1 255.255.255.0
R3(config-if)#no shut
R3(config-if)#inter fa1/1
R3(config-if)#switchport mode trunk
R3(config-if)#switchport trunk encapsulation dot1q
R3(config-if)#inter f0/0
R3(config-if)#sw
R3(config-if)#ip add
R3(config-if)#ip address 192.168.100.10 255.255.255.0
ig-if)#no shut
R3(config-if)#inter fa1
R3(config-if)#inter fa1/2
R3(config-if)#no switchport
R3(config-if)#ip address 192.168.200.10 255.255.255.0
R3(config-if)#no shut
R3(config)#ip default-gateway 192.168.100.1
R3(config)#ip route 0.0.0.0 0.0.0.0 192.168.200.1
R3#ping 192.168.200.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.200.1, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 16/31/52 ms
R3#ping 202.106.1.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 202.106.1.2, timeout is 2 seconds:
!!!!!

R3要有3条直连路由。一条默认路由。 R1要有2条直连和两条静态

在出口路由上配置！

interface FastEthernet0/0
ip address 192.168.200.1 255.255.255.0
ip nat inside

interface FastEthernet0/1
ip address 202.106.1.1 255.255.255.252
ip nat outside
ip virtual-reassembly
duplex auto
speed auto

ip route 192.168.10.0 255.255.255.0 192.168.200.10
ip route 192.168.20.0 255.255.255.0 192.168.200.10

ip nat inside source list 1 interface FastEthernet0/1 overload
access-list 1 permit 192.168.0.0 0.0.255.255

S    192.168.10.0/24 [1/0] via 192.168.200.10
     202.106.1.0/30 is subnetted, 1 subnets
C       202.106.1.0 is directly connected, FastEthernet0/1
C    192.168.200.0/24 is directly connected, FastEthernet0/0
S    192.168.20.0/24 [1/0] via 192.168.200.10
R1#ping 202.106.1.2 source 192.168.200.1
Sending 5, 100-byte ICMP Echos to 202.106.1.2, timeout is 2 seconds:
Packet sent with a source address of 192.168.200.1
.!!!!

R4>en
R4#conf t
R4(config)#inter fa0/0
R4(config-if)#ip address 202.106.1.2 255.255.255.252
R4(config-if)#no shut

ok ping通外网了！

本文转自 cs312779641 51CTO博客，原文链接:http://blog.51cto.com/chenhao6/1162255

DHCP中继 NAT 让客户端自动获取ip地址并ping通外网！

热门文章

最新文章

相关课程

相关电子书

相关实验场景

DHCP中继 NAT 让客户端自动获取ip地址 并ping通外网！

热门文章

最新文章

相关课程

相关电子书

相关实验场景

DHCP中继 NAT 让客户端自动获取ip地址并ping通外网！