搭建流程
1.配置网络，主机名（双节点）
controller：192.168.1.10 192.168.2.10 compute：192.168.1.20 192.168.2.20 controller配置： [root@controller ~]# hostnamectl set-hostname controller [root@controller ~]# logout 重连登录 [root@controller ~]# vi /etc/sysconfig/network-scripts/ifcfg-eno16777728 TYPE=Ethernet BOOTPROTO=static DEFROUTE=yes PEERDNS=yes PEERROUTES=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=eno16777728 UUID=33c092da-748f-4504-b735-d9dff2a49d33 DEVICE=eno16777728 ONBOOT=yes IPADDR=192.168.1.10 PREFIX=24 GATEWAY=192.168.1.1 [root@controller ~]# cd /etc/sysconfig/network-scripts/ [root@controller network-scripts]# cp -a ifcfg-eno16777728 ifcfg-eno33554960 [root@controller network-scripts]# vi /etc/sysconfig/network-scripts/ifcfg-eno33554960 DEVICE=eno33554960 TYPE=Ethernet BOOTPROTO=none ONBOOT=yes IPADDR=192.168.2.10 PREFIX=24 [root@controller ~]# systemctl restart network [root@controller ~]# ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eno16777728: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:01:7e:b7 brd ff:ff:ff:ff:ff:ff inet 192.168.1.10/24 brd 192.168.1.255 scope global eno16777728 valid_lft forever preferred_lft forever inet6 fe80::20c:29ff:fe01:7eb7/64 scope link valid_lft forever preferred_lft forever 3: eno33554960: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master ovs-system state UP qlen 1000 link/ether 00:0c:29:01:7e:c1 brd ff:ff:ff:ff:ff:ff inet 192.168.2.10/24 brd 192.168.2.255 scope global eno33554960 valid_lft forever preferred_lft forever inet6 fe80::20c:29ff:fe01:7ec1/64 scope link valid_lft forever preferred_lft forever 关机直接克隆compute compute配置： [root@compute ~]# hostnamectl set-hostname compute [root@compute ~]# logout 重连登录 [root@compute ~]# vi /etc/sysconfig/network-scripts/ifcfg-eno16777728 TYPE=Ethernet BOOTPROTO=static DEFROUTE=yes PEERDNS=yes PEERROUTES=yes IPV4_FAILURE_FATAL=no IPV6INIT=yes IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no NAME=eno16777728 UUID=33c092da-748f-4504-b735-d9dff2a49d33 DEVICE=eno16777728 ONBOOT=yes IPADDR=192.168.1.20 PREFIX=24 [root@compute ~]# cd /etc/sysconfig/network-scripts/ [root@compute network-scripts]# cp -a ifcfg-eno16777728 ifcfg-eno33554960 [root@compute network-scripts]# vi /etc/sysconfig/network-scripts/ifcfg-eno33554960 DEVICE=eno33554960 TYPE=Ethernet BOOTPROTO=none ONBOOT=yes IPADDR=192.168.2.20 PREFIX=24 [root@compute ~]# systemctl restart network [root@compute ~]# ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eno16777728: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:01:7e:b7 brd ff:ff:ff:ff:ff:ff inet 192.168.1.20/24 brd 192.168.1.255 scope global eno16777728 valid_lft forever preferred_lft forever inet6 fe80::20c:29ff:fe01:7eb7/64 scope link valid_lft forever preferred_lft forever 3: eno33554960: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master ovs-system state UP qlen 1000 link/ether 00:0c:29:01:7e:c1 brd ff:ff:ff:ff:ff:ff inet 192.168.2.20/24 brd 192.168.2.255 scope global eno33554960 valid_lft forever preferred_lft forever inet6 fe80::20c:29ff:fe01:7ec1/64 scope link valid_lft forever preferred_lft forever 记得拉取两个镜像！！！（只需要在controller节点拉取）
2.永久闭防火墙和selinux（双节点）
[root@controller yum.repos.d]# systemctl stop firewalld [root@controller yum.repos.d]# systemctl disable firewalld Removed symlink /etc/systemd/system/dbus-org.fedoraproject.FirewallD1.service. Removed symlink /etc/systemd/system/basic.target.wants/firewalld.service. [root@controller yum.repos.d]# setenforce 0 [root@controller yum.repos.d]# vi /etc/selinux/config # This file controls the state of SELinux on the system. # SELINUX= can take one of these three values: # enforcing - SELinux security policy is enforced. # permissive - SELinux prints warnings instead of enforcing. # disabled - No SELinux policy is loaded. SELINUX=disabled # SELINUXTYPE= can take one of three two values: # targeted - Targeted processes are protected, # minimum - Modification of targeted policy. Only selected processes are protected. # mls - Multi Level Security protection. SELINUXTYPE=targeted [root@compute yum.repos.d]# systemctl stop firewalld [root@compute yum.repos.d]# systemctl disable firewalld Removed symlink /etc/systemd/system/dbus-org.fedoraproject.FirewallD1.service. Removed symlink /etc/systemd/system/basic.target.wants/firewalld.service. [root@compute yum.repos.d]# setenforce 0 [root@compute yum.repos.d]# vi /etc/selinux/config # This file controls the state of SELinux on the system. # SELINUX= can take one of these three values: # enforcing - SELinux security policy is enforced. # permissive - SELinux prints warnings instead of enforcing. # disabled - No SELinux policy is loaded. SELINUX=disabled # SELINUXTYPE= can take one of three two values: # targeted - Targeted processes are protected, # minimum - Modification of targeted policy. Only selected processes are protected. # mls - Multi Level Security protection. SELINUXTYPE=targeted
3.配置YUM源（双节点）
配置主机名映射 [root@controller ~]# vi /etc/hosts 192.168.1.10 controller 192.168.1.20 compute 127.0.0.1 localhost localhost.localdomain localhost4 localhost4.localdomain4 ::1 localhost localhost.localdomain localhost6 localhost6.localdomain6 [root@compute ~]# vi /etc/hosts 192.168.1.10 controller 192.168.1.20 compute 127.0.0.1 localhost localhost.localdomain localhost4 localhost4.localdomain4 ::1 localhost localhost.localdomain localhost6 localhost6.localdomain6 [root@controller ~]# cd /etc/yum.repos.d/ [root@controller yum.repos.d]# rm -rf * [root@controller yum.repos.d]# cat local.repo [centos] name=centos baseurl=file:///opt/centos gpgcheck=0 enabled=1 [iaas] name=iaas baseurl=file:///opt/iaas/iaas-repo gpgcheck=0 enabled=1 [root@compute ~]# cd /etc/yum.repos.d/ [root@compute yum.repos.d]# rm -rf * [root@compute yum.repos.d]# cat local.repo [centos] name=centos baseurl=ftp://controller/centos gpgcheck=0 enabled=1 [iaas] name=iaas baseurl=ftp://controller/iaas/iaas-repo gpgcheck=0 enabled=1
4.写入/etc/fstab,并挂载镜像
[root@controller ~]# ls anaconda-ks.cfg CentOS-7-x86_64-DVD-1511.iso XianDian-IaaS-v2.2.iso [root@controller ~]# mkdir /opt/centos [root@controller ~]# mkdir /opt/iaas [root@controller ~]# cat /etc/fstab # # /etc/fstab # Created by anaconda on Thu Oct 1 06:46:45 2020 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # UUID=36615874-b25f-4539-b376-8a5c387c0212 / xfs defaults 0 0 UUID=02223747-779a-4b6d-a300-2774ec29a144 /boot xfs defaults 0 0 UUID=01956b4a-500a-4f23-8b60-75b3bb457ded swap swap defaults 0 0 /root/CentOS-7-x86_64-DVD-1511.iso /opt/centos iso9660 defaults 0 0 /root/XianDian-IaaS-v2.2.iso /opt/iaas iso9660 defaults 0 0 [root@controller ~]# mount -a mount: /dev/loop0 is write-protected, mounting read-only mount: /dev/loop1 is write-protected, mounting read-only [root@controller ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 98G 7.6G 90G 8% / devtmpfs 904M 0 904M 0% /dev tmpfs 913M 0 913M 0% /dev/shm tmpfs 913M 8.5M 904M 1% /run tmpfs 913M 0 913M 0% /sys/fs/cgroup /dev/sda1 497M 118M 380M 24% /boot tmpfs 183M 0 183M 0% /run/user/0 /dev/loop0 4.1G 4.1G 0 100% /opt/centos /dev/loop1 2.7G 2.7G 0 100% /opt/iaas [root@controller ~]# yum list [root@controller ~]# yum install -y vim [root@controller ~]# yum install -y vsftpd [root@controller ~]# cat /etc/vsftpd/vsftpd.conf (在第一行添加下面内容，点点不用写) anon_root=/opt/ ... ... [root@controller ~]# systemctl restart vsftpd [root@controller ~]# systemctl enable vsftpd Created symlink from /etc/systemd/system/multi-user.target.wants/vsftpd.service to /usr/lib/systemd/system/vsftpd.service.
5.安装iaas相关软件包
[root@controller ~]# yum install -y iaas-xiandian [root@compute ~]# yum install -y iaas-xiandian
6.划分磁盘作为swift和cinder
[root@computer ~]# fdisk -l Disk /dev/sda: 21.5 GB, 21474836480 bytes, 41943040 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk label type: dos Disk identifier: 0x0002f10c Device Boot Start End Blocks Id System /dev/sda1 2048 4196351 2097152 82 Linux swap / Solaris /dev/sda2 * 4196352 41943039 18873344 83 Linux Disk /dev/sdb: 107.4 GB, 107374182400 bytes, 209715200 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes [root@computer ~]# fdisk /dev/sdb Welcome to fdisk (util-linux 2.23.2). Changes will remain in memory only, until you decide to write them. Be careful before using the write command. Device does not contain a recognized partition table Building a new DOS disklabel with disk identifier 0xa5eb8d25. Command (m for help): n Partition type: p primary (0 primary, 0 extended, 4 free) e extended Select (default p): Using default response p Partition number (1-4, default 1): First sector (2048-209715199, default 2048): Using default value 2048 Last sector, +sectors or +size{K,M,G} (2048-209715199, default 209715199): +30G Partition 1 of type Linux and of size 30 GiB is set Command (m for help): n Partition type: p primary (1 primary, 0 extended, 3 free) e extended Select (default p): Using default response p Partition number (2-4, default 2): First sector (62916608-209715199, default 62916608): Using default value 62916608 Last sector, +sectors or +size{K,M,G} (62916608-209715199, default 209715199): +30G Partition 2 of type Linux and of size 30 GiB is set Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table. Syncing disks. [root@computer ~]# fdisk -l Disk /dev/sda: 21.5 GB, 21474836480 bytes, 41943040 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk label type: dos Disk identifier: 0x0002f10c Device Boot Start End Blocks Id System /dev/sda1 2048 4196351 2097152 82 Linux swap / Solaris /dev/sda2 * 4196352 41943039 18873344 83 Linux Disk /dev/sdb: 107.4 GB, 107374182400 bytes, 209715200 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk label type: dos Disk identifier: 0xa5eb8d25 Device Boot Start End Blocks Id System /dev/sdb1 2048 62916607 31457280 83 Linux /dev/sdb2 62916608 125831167 31457280 83 Linux [root@compute ~]# mkfs.xfs /dev/sdb1 [root@compute ~]# mkfs.xfs /dev/sdb2
7.修改环境变量
[root@controller ~]# cat /etc/xiandian/openrc.sh cat /etc/xiandian/openrc.sh ##--------------------system Config--------------------## ##Controller Server Manager IP. example:x.x.x.x HOST_IP=192.168.1.10 ##Controller Server hostname. example:controller HOST_NAME=controller ##Compute Node Manager IP. example:x.x.x.x HOST_IP_NODE=192.168.1.20 ##Compute Node hostname. example:compute HOST_NAME_NODE=compute ##--------------------Rabbit Config ------------------## ##user for rabbit. example:openstack RABBIT_USER=openstack ##Password for rabbit user .example:000000 RABBIT_PASS=a ##--------------------MySQL Config---------------------## ##Password for MySQL root user . exmaple:000000 DB_PASS=a ##--------------------Keystone Config------------------## ##Password for Keystore admin user. exmaple:000000 DOMAIN_NAME=lyb ADMIN_PASS=a DEMO_PASS=a ##Password for Mysql keystore user. exmaple:000000 KEYSTONE_DBPASS=a ##--------------------Glance Config--------------------## ##Password for Mysql glance user. exmaple:000000 GLANCE_DBPASS=a ##Password for Keystore glance user. exmaple:000000 GLANCE_PASS=a ##--------------------Nova Config----------------------## ##Password for Mysql nova user. exmaple:000000 NOVA_DBPASS=a ##Password for Keystore nova user. exmaple:000000 NOVA_PASS=a ##--------------------Neturon Config-------------------## ##Password for Mysql neutron user. exmaple:000000 NEUTRON_DBPASS=a ##Password for Keystore neutron user. exmaple:000000 NEUTRON_PASS=a ##metadata secret for neutron. exmaple:000000 METADATA_SECRET=a ##External Network Interface. example:eth1 INTERFACE_NAME=eno33554960 ##First Vlan ID in VLAN RANGE for VLAN Network. exmaple:101 #minvlan= ##Last Vlan ID in VLAN RANGE for VLAN Network. example:200 #maxvlan= ##--------------------Cinder Config--------------------## ##Password for Mysql cinder user. exmaple:000000 CINDER_DBPASS=a ##Password for Keystore cinder user. exmaple:000000 CINDER_PASS=a ##Cinder Block Disk. example:md126p3 BLOCK_DISK=/dev/sdb1 ##--------------------Trove Config--------------------## ##Password for Mysql Trove User. exmaple:000000 TROVE_DBPASS=a ##Password for Keystore Trove User. exmaple:000000 TROVE_PASS=a ##--------------------Swift Config---------------------## ##Password for Keystore swift user. exmaple:000000 SWIFT_PASS=a ##The NODE Object Disk for Swift. example:md126p4. OBJECT_DISK=/dev/sdb2 ##The NODE IP for Swift Storage Network. example:x.x.x.x. STORAGE_LOCAL_NET_IP=192.168.1.20 ##--------------------Heat Config----------------------## ##Password for Mysql heat user. exmaple:000000 HEAT_DBPASS=a ##Password for Keystore heat user. exmaple:000000 HEAT_PASS=a ##--------------------Ceilometer Config----------------## ##Password for Mysql ceilometer user. exmaple:000000 CEILOMETER_DBPASS=a ##Password for Keystore ceilometer user. exmaple:000000 CEILOMETER_PASS=a ##--------------------AODH Config----------------## ##Password for Mysql AODH user. exmaple:000000 AODH_DBPASS=a ##Password for Keystore AODH user. exmaple:000000 AODH_PASS=a [root@controller ~]# scp /etc/xiandian/openrc.sh root@compute:/etc/xiandian/openrc.sh
8.配置NTP服务
新版本不用更改
9.通过脚本安装服务
控制节点
iaas-pre-host.sh reboot iaas-install-mysql.sh iaas-install-keystone.sh iaas-install-glance.sh iaas-install-nova-controller.sh iaas-install-neutron-controller.sh iaas-install-dashboard.sh 计算节点 iaas-pre-host.sh reboot iaas-install-nova-compute.sh iaas-install-neutron-compute.sh
10.通过IP访问云平台
http://192.168.1.10/dashboard
11.测试
登录会有点卡
12.附录（用xshell连接虚拟机）
怎么用XSHELL连接虚拟机？
统一用桥接模式
1.查看本地wife属型（可以看出本地wife是192.168.1.0网段）
我拿controller节点举例子
1.设置网卡模式为桥接模式
2.配置IP和wife网段一致
也就是192.168.1.0网段
3.用xshell进行连接
4.连接成功
完成啦，记得一键三连哦！
![[ 云计算相关 ] KVM虚拟化平台windows虚拟机迁移到openstack虚拟化平台（KVM虚拟化环境中Windows虚拟机安装Virtio驱动程序）](https://ucc.alicdn.com/pic/developer-ecology/c1e29a24cc8e47b9999c95c6c8cd7cdd.png?x-oss-process=image/resize,h_160,m_lfit)
