版权声明：本文为博主原创文章，未经博主允许不得转载。 https://blog.csdn.net/qq1010885678/article/details/44902601
1.修改主机名：
vim /etc/sysconfig/network
NETWORKING=yes
HOSTNAME=MASTER
2.修改IP：
先用ifconfig得到ip信息，将其复制
设置ip地址为静态
vim /etc/sysconfig/network-scripts/ifcfg-eth0
BOOTPROTO="static"
HWADDR="00:0C:29:FC:62:B6"
IPV6INIT="yes"
NM_CONTROLLED="yes"
ONBOOT="yes"
TYPE="Ethernet"
UUID="d0731a46-36df-4ab1-9bac-42bb151acc41"
IPADDR="192.168.1.250"
NETMASK="255.255.255.0"
GATEWAY="192.168.1.1"
DNS1="8.8.8.8"
DNS2="8.8.4.4"
3.修改主机和IP的映射关系
vim /etc/hosts
4.关闭防火墙
5.上传安装jdk，配置环境变量
上传
zeromq-2.1.7.tar.gz
jzmq-master.zip
storm-0.8.2.zip
zookeeper-3.4.5.tar.gz
等文件
1.编译安装ZMQ：
tar -xzf zeromq-2.1.7.tar.gz
cd zeromq-2.1.7
./configure
#编译可能会出错：configure: error: Unable to find a working C++ compiler
#安装一下依赖的rpm包（在vm虚拟机中加载安装的cd盘文件，里面的services文件夹有所有的包）：
libstdc++-devel
gcc-c++
libuuid-devel
./configure
make
make install
2.编译安装JZMQ：
cd jzmq
./autogen.sh
#报错:autogen.sh: error: could not find libtool. libtool is required to run autogen.sh.
缺少libtool
yum install libtool
或者手动安装
autoconf-2.63-5.1.el6.noarch.rpm
automake-1.11.1-4.el6.noarch.rpm
libtool-2.2.6-15.5.el6.x86_64.rpm
./configure
make
make install
3.安装启动zookeeper
4.上传解压storm
进入conf目录
修改storm.yaml
#zookeeper的节点
storm.zookeeper.servers:
- "cloud4"
- "cloud5"
- "cloud6"
#nimbus主节点
nimbus.host: "cloud4"
vim /etc/sysconfig/network
NETWORKING=yes
HOSTNAME=MASTER
2.修改IP：
先用ifconfig得到ip信息，将其复制
设置ip地址为静态
vim /etc/sysconfig/network-scripts/ifcfg-eth0
BOOTPROTO="static"
HWADDR="00:0C:29:FC:62:B6"
IPV6INIT="yes"
NM_CONTROLLED="yes"
ONBOOT="yes"
TYPE="Ethernet"
UUID="d0731a46-36df-4ab1-9bac-42bb151acc41"
IPADDR="192.168.1.250"
NETMASK="255.255.255.0"
GATEWAY="192.168.1.1"
DNS1="8.8.8.8"
DNS2="8.8.4.4"
3.修改主机和IP的映射关系
vim /etc/hosts
4.关闭防火墙
5.上传安装jdk，配置环境变量
上传
zeromq-2.1.7.tar.gz
jzmq-master.zip
storm-0.8.2.zip
zookeeper-3.4.5.tar.gz
等文件
1.编译安装ZMQ：
tar -xzf zeromq-2.1.7.tar.gz
cd zeromq-2.1.7
./configure
#编译可能会出错：configure: error: Unable to find a working C++ compiler
#安装一下依赖的rpm包（在vm虚拟机中加载安装的cd盘文件，里面的services文件夹有所有的包）：
libstdc++-devel
gcc-c++
libuuid-devel
./configure
make
make install
2.编译安装JZMQ：
cd jzmq
./autogen.sh
#报错:autogen.sh: error: could not find libtool. libtool is required to run autogen.sh.
缺少libtool
yum install libtool
或者手动安装
autoconf-2.63-5.1.el6.noarch.rpm
automake-1.11.1-4.el6.noarch.rpm
libtool-2.2.6-15.5.el6.x86_64.rpm
./configure
make
make install
3.安装启动zookeeper
4.上传解压storm
进入conf目录
修改storm.yaml
#zookeeper的节点
storm.zookeeper.servers:
- "cloud4"
- "cloud5"
- "cloud6"
#nimbus主节点
nimbus.host: "cloud4"
启动nimbus
输出日志到null下
在后台运行
./storm nimbus > ../dev/null 2>&1 &
