Redis3.2开启远程访问
环境
安装环境：win7系统
Redis版本：3.2.100
安装模式：msi文件安装
开启远程访问
Redis安装完之后，在服务中可以看到对应的Redis服务，打开属性，可以看到“可执行文件的路径”是：”D:\Program Files\Redis\redis-server.exe” –service-run “D:\Program Files\Redis\redis.windows-service.conf”
开启Redis远程访问的步骤如下：
- 打开redis.windows-service.conf
- 找到“bind 127.0.0.1”并在前面加#注释
- 找到“protected-mode yes”并改为“protected-mode no”
配置如下：
################################## NETWORK #####################################
# By default, if no "bind" configuration directive is specified, Redis listens
# for connections from all the network interfaces available on the server.
# It is possible to listen to just one or multiple selected interfaces using
# the "bind" configuration directive, followed by one or more IP addresses.
#
# Examples:
#
# bind 192.168.1.100 10.0.0.1
# bind 127.0.0.1 ::1
#
# ~~~ WARNING ~~~ If the computer running Redis is directly exposed to the
# internet, binding to all the interfaces is dangerous and will expose the
# instance to everybody on the internet. So by default we uncomment the
# following bind directive, that will force Redis to listen only into
# the IPv4 lookback interface address (this means Redis will be able to
# accept connections only from clients running into the same computer it
# is running).
#
# IF YOU ARE SURE YOU WANT YOUR INSTANCE TO LISTEN TO ALL THE INTERFACES
# JUST COMMENT THE FOLLOWING LINE.
# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
# bind 127.0.0.1
# Protected mode is a layer of security protection, in order to avoid that
# Redis instances left open on the internet are accessed and exploited.
#
# When protected mode is on and if:
#
# 1) The server is not binding explicitly to a set of addresses using the
# "bind" directive.
# 2) No password is configured.
#
# The server only accepts connections from clients connecting from the
# IPv4 and IPv6 loopback addresses 127.0.0.1 and ::1, and from Unix domain
# sockets.
#
# By default protected mode is enabled. You should disable it only if
# you are sure you want clients from other hosts to connect to Redis
# even if no authentication is configured, nor a specific set of interfaces
# are explicitly listed using the "bind" directive.
protected-mode no
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
解决的过程
由于百度得到的答案基本都是说把“bind 127.0.0.1”注释掉就可以了，根据配置文件的描述，也确实是要注释掉才可以被其他机器访问到，配置完重启，通过其他机器的redis-cli客户端进行连接，连接命令：redis-cli -h 172.16.8.200 -p 6379
意外的发现竟然连上了，于是随表敲一个命令，比如info，出现了如下提示：
通过阅读提示，在配置文件中找到protected-mode，并将其值改为no，重启之后，问题解决了。
原文地址https://blog.csdn.net/u010956470/article/details/64440983
