linux 的ping 命令

简介:

Linux系统的ping命令是常用的网络命令,它通常用来测试与目标主机的连通性,我们经常会说“ping一下某机器,看是不是开着”、不能打开网页时会说“你先ping网关地址192.168.1.1试试”。它通过发送ICMP ECHO_REQUEST数据包到网络主机(send ICMP ECHO_REQUEST to network hosts),并显示响应情况,这样我们就可以根据它输出的信息来确定目标主机是否可访问(但这不是绝对的)。有些服务器为了防止通过ping探测到,通过防火墙设置了禁止ping或者在内核参数中禁止ping,这样就不能通过ping确定该主机是否还处于开启状态。

linux下的ping和windows下的ping稍有区别,linux下ping不会自动终止,需要按ctrl+c终止或者用参数-c指定要求完成的回应次数

1.命令格式:

ping [参数] [主机名或IP地址]

2.命令功能:

ping命令用于:确定网络和各外部主机的状态跟踪和隔离硬件和软件问题测试、评估和管理网络。如果主机正在运行并连在网上,它就对回送信号进行响应。每个回送信号请求包含一个网际协议(IP)和 ICMP 头,后面紧跟一个 tim 结构,以及来填写这个信息包的足够的字节。缺省情况是连续发送回送信号请求直到接收到中断信号(Ctrl-C)。

ping 命令每秒发送一个数据报并且为每个接收到的响应打印一行输出。ping 命令计算信号往返时间和(信息)包丢失情况的统计信息,并且在完成之后显示一个简要总结。ping 命令在程序超时或当接收到 SIGINT 信号时结束。Host 参数或者是一个有效的主机名或者是因特网地址。

3.命令参数:

-d 使用Socket的SO_DEBUG功能。

-f  极限检测。大量且快速地送网络封包给一台机器,看它的回应。

-n 只输出数值。

-q 不显示任何传送封包的信息,只显示最后的结果。

-r 忽略普通的Routing Table,直接将数据包送到远端主机上。通常是查看本机的网络接口是否有问题。

-R 记录路由过程。

-v 详细显示指令的执行过程。

<p>-c 数目在发送指定数目的包后停止。

-i 秒数设定间隔几秒送一个网络封包给一台机器,预设值是一秒送一次。

-I 网络界面使用指定的网络界面送出数据包。

-l 前置载入设置在送出要求信息之前,先行发出的数据包。

-p 范本样式设置填满数据包的范本样式。

-s 字节数指定发送的数据字节数,预设值是56,加上8字节的ICMP头,一共是64ICMP数据字节。

-t 存活数值设置存活数值TTL的大小。


4.使用实例:

实例1:ping的通的情况

命令:

ping 192.168.120.205

输出:



1
2
3
4
5
6
7
8
9
10
11
12
[root@localhost ~]# ping 192.168.120.205
PING 192.168.120.205 (192.168.120.205) 56(84) bytes of data.
64 bytes from 192.168.120.205: icmp_seq=1 ttl=64 time=0.720 ms
64 bytes from 192.168.120.205: icmp_seq=2 ttl=64 time=0.181 ms
64 bytes from 192.168.120.205: icmp_seq=3 ttl=64 time=0.191 ms
64 bytes from 192.168.120.205: icmp_seq=4 ttl=64 time=0.188 ms
64 bytes from 192.168.120.205: icmp_seq=5 ttl=64 time=0.189 ms
 
--- 192.168.120.205 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4000ms
rtt min/avg/max/mdev = 0.181/0.293/0.720/0.214 ms
[root@localhost ~]#


说明:

 


实例2:ping不通的情况

命令:

ping 192.168.120.202

输出:


1
2
3
4
5
6
7
8
9
10
11
12
13
[root@localhost ~]# ping 192.168.120.202
PING 192.168.120.202 (192.168.120.202) 56(84) bytes of data.
From 192.168.120.204 icmp_seq=1 Destination Host Unreachable
From 192.168.120.204 icmp_seq=2 Destination Host Unreachable
From 192.168.120.204 icmp_seq=3 Destination Host Unreachable
From 192.168.120.204 icmp_seq=4 Destination Host Unreachable
From 192.168.120.204 icmp_seq=5 Destination Host Unreachable
From 192.168.120.204 icmp_seq=6 Destination Host Unreachable
 
--- 192.168.120.202 ping statistics ---
8 packets transmitted, 0 received, +6 errors, 100% packet loss, time 7005ms
, pipe 4
[root@localhost ~]#


说明:

 


实例3:ping网关

命令:

ping -b 192.168.120.1

输出:

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
[root@localhost ~]# route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.120.0   *               255.255.255.0   U     0      0        0 eth0
192.168.0.0     192.168.120.1   255.255.0.0     UG    0      0        0 eth0
10.0.0.0        192.168.120.1   255.0.0.0       UG    0      0        0 eth0
default         192.168.120.240 0.0.0.0         UG    0      0        0 eth0
[root@localhost ~]# ping -b 192.168.120.1
PING 192.168.120.1 (192.168.120.1) 56(84) bytes of data.
64 bytes from 192.168.120.1: icmp_seq=1 ttl=255 time=2.02 ms
64 bytes from 192.168.120.1: icmp_seq=2 ttl=255 time=1.83 ms
64 bytes from 192.168.120.1: icmp_seq=3 ttl=255 time=1.68 ms
64 bytes from 192.168.120.1: icmp_seq=4 ttl=255 time=1.98 ms
64 bytes from 192.168.120.1: icmp_seq=5 ttl=255 time=1.88 ms
 
--- 192.168.120.1 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4000ms
rtt min/avg/max/mdev = 1.682/1.880/2.020/0.129 ms

说明:  ping网关要加上-b参数

 


实例4:ping指定次数

命令:

ping -c 10 192.168.120.206

输出:

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
[root@localhost ~]# ping -c 10 192.168.120.206
PING 192.168.120.206 (192.168.120.206) 56(84) bytes of data.
64 bytes from 192.168.120.206: icmp_seq=1 ttl=64 time=1.25 ms
64 bytes from 192.168.120.206: icmp_seq=2 ttl=64 time=0.260 ms
64 bytes from 192.168.120.206: icmp_seq=3 ttl=64 time=0.242 ms
64 bytes from 192.168.120.206: icmp_seq=4 ttl=64 time=0.271 ms
64 bytes from 192.168.120.206: icmp_seq=5 ttl=64 time=0.274 ms
64 bytes from 192.168.120.206: icmp_seq=6 ttl=64 time=0.295 ms
64 bytes from 192.168.120.206: icmp_seq=7 ttl=64 time=0.269 ms
64 bytes from 192.168.120.206: icmp_seq=8 ttl=64 time=0.270 ms
64 bytes from 192.168.120.206: icmp_seq=9 ttl=64 time=0.253 ms
64 bytes from 192.168.120.206: icmp_seq=10 ttl=64 time=0.289 ms
 
--- 192.168.120.206 ping statistics ---
10 packets transmitted, 10 received, 0% packet loss, time 9000ms
rtt min/avg/max/mdev = 0.242/0.367/1.251/0.295 ms
[root@localhost ~]#


说明:-c指定ping的次数

 


实例5:时间间隔和次数限制的ping

命令:

ping -c 10 -i 0.5 192.168.120.206

输出:


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
[root@localhost ~]# ping -c 10 -i 0.5 192.168.120.206
PING 192.168.120.206 (192.168.120.206) 56(84) bytes of data.
64 bytes from 192.168.120.206: icmp_seq=1 ttl=64 time=1.24 ms
64 bytes from 192.168.120.206: icmp_seq=2 ttl=64 time=0.235 ms
64 bytes from 192.168.120.206: icmp_seq=3 ttl=64 time=0.244 ms
64 bytes from 192.168.120.206: icmp_seq=4 ttl=64 time=0.300 ms
64 bytes from 192.168.120.206: icmp_seq=5 ttl=64 time=0.255 ms
64 bytes from 192.168.120.206: icmp_seq=6 ttl=64 time=0.264 ms
64 bytes from 192.168.120.206: icmp_seq=7 ttl=64 time=0.263 ms
64 bytes from 192.168.120.206: icmp_seq=8 ttl=64 time=0.331 ms
64 bytes from 192.168.120.206: icmp_seq=9 ttl=64 time=0.247 ms
64 bytes from 192.168.120.206: icmp_seq=10 ttl=64 time=0.244 ms
 
--- 192.168.120.206 ping statistics ---
10 packets transmitted, 10 received, 0% packet loss, time 4499ms
rtt min/avg/max/mdev = 0.235/0.362/1.241/0.294 ms
[root@localhost ~]# ping -c 10 -i 0.01 192.168.120.206
PING 192.168.120.206 (192.168.120.206) 56(84) bytes of data.
64 bytes from 192.168.120.206: icmp_seq=1 ttl=64 time=0.244 ms
64 bytes from 192.168.120.206: icmp_seq=2 ttl=64 time=0.195 ms
64 bytes from 192.168.120.206: icmp_seq=3 ttl=64 time=0.219 ms
64 bytes from 192.168.120.206: icmp_seq=4 ttl=64 time=0.204 ms
64 bytes from 192.168.120.206: icmp_seq=5 ttl=64 time=3.56 ms
64 bytes from 192.168.120.206: icmp_seq=6 ttl=64 time=1.93 ms
64 bytes from 192.168.120.206: icmp_seq=7 ttl=64 time=0.193 ms
64 bytes from 192.168.120.206: icmp_seq=8 ttl=64 time=0.193 ms
64 bytes from 192.168.120.206: icmp_seq=9 ttl=64 time=0.202 ms
64 bytes from 192.168.120.206: icmp_seq=10 ttl=64 time=0.211 ms
 
--- 192.168.120.206 ping statistics ---
10 packets transmitted, 10 received, 0% packet loss, time 90ms
rtt min/avg/max/mdev = 0.193/0.716/3.564/1.080 ms
[root@localhost ~]#


 

说明:-i指定ping次数的时间间隔,不指定则默认1s

 


实例6:通过域名ping公网上的站点

命令:

ping -c 5 www.58.com

输出:


1
2
3
4
5
6
7
8
9
10
11
12
peida-VirtualBox ~ # ping -c 5 www.58.com
PING www.58.com (211.151.111.30) 56(84) bytes of data.
64 bytes from 211.151.111.30: icmp_req=1 ttl=49 time=14.7 ms
64 bytes from 211.151.111.30: icmp_req=2 ttl=49 time=16.4 ms
64 bytes from 211.151.111.30: icmp_req=3 ttl=49 time=15.2 ms
64 bytes from 211.151.111.30: icmp_req=4 ttl=49 time=14.6 ms
64 bytes from 211.151.111.30: icmp_req=5 ttl=49 time=19.9 ms
 
--- www.58.com ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 20101ms
rtt min/avg/max/mdev = 14.618/16.192/19.917/1.965 ms
peida-VirtualBox ~ #

说明:

 


实例7:多参数使用

命令:

ping -i 3 -s 1024 -t 255 192.168.120.206

输出:


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
[root@localhost ~]# ping -i 3 -s 1024 -t 255 192.168.120.206
PING 192.168.120.206 (192.168.120.206) 1024(1052) bytes of data.
1032 bytes from 192.168.120.206: icmp_seq=1 ttl=64 time=1.99 ms
1032 bytes from 192.168.120.206: icmp_seq=2 ttl=64 time=0.694 ms
1032 bytes from 192.168.120.206: icmp_seq=3 ttl=64 time=0.300 ms
1032 bytes from 192.168.120.206: icmp_seq=4 ttl=64 time=0.481 ms
1032 bytes from 192.168.120.206: icmp_seq=5 ttl=64 time=0.415 ms
1032 bytes from 192.168.120.206: icmp_seq=6 ttl=64 time=0.600 ms
1032 bytes from 192.168.120.206: icmp_seq=7 ttl=64 time=0.411 ms
1032 bytes from 192.168.120.206: icmp_seq=8 ttl=64 time=0.281 ms
1032 bytes from 192.168.120.206: icmp_seq=9 ttl=64 time=0.318 ms
1032 bytes from 192.168.120.206: icmp_seq=10 ttl=64 time=0.362 ms
1032 bytes from 192.168.120.206: icmp_seq=11 ttl=64 time=0.408 ms
1032 bytes from 192.168.120.206: icmp_seq=12 ttl=64 time=0.445 ms
1032 bytes from 192.168.120.206: icmp_seq=13 ttl=64 time=0.397 ms
1032 bytes from 192.168.120.206: icmp_seq=14 ttl=64 time=0.406 ms
1032 bytes from 192.168.120.206: icmp_seq=15 ttl=64 time=0.458 ms
 
--- 192.168.120.206 ping statistics ---
15 packets transmitted, 15 received, 0% packet loss, time 41999ms
rtt min/avg/max/mdev = 0.281/0.531/1.993/0.404 ms
[root@localhost ~]#


说明:

-i 3 发送周期为 3秒 -s 设置发送包的大小1024 -t 设置TTL值为 255








     本文转自布拉君君 51CTO博客,原文链接 http://blog.51cto.com/5148737/1546001 :,如需转载请自行联系原作者

相关文章
|
22天前
|
Linux
linux命令详细说明以及案例
本文介绍了常用的 Linux 命令及其详细说明和示例,包括:`ls`(列出目录内容)、`cd`(更改目录)、`rm` 和 `mv`(删除与移动文件)、`grep`(搜索文本)、`cat`(显示文件内容)以及 `chmod`(更改文件权限)。每个命令均配有功能描述、选项说明及实际案例,帮助用户更好地掌握 Linux 命令的使用方法。
125 56
|
8天前
|
Linux 定位技术
Linux系统中的cd命令:目录切换技巧
踏过千山,越过万水,人生就是一场不断前行的旅程,总充满了未知与挑战。然而,“cd”命令如同你的旅伴,会带你穿梭在如棋盘一般的文件系统中,探索每一处未知。希望你能从“cd”命令中找到乐趣,像是掌控了一种络新妙的魔法,去向未知进发,开始你的探索之旅。
80 24
|
10天前
|
安全 Shell Linux
Linux系统之su命令的基本使用
Linux系统之su命令的基本使用
48 2
Linux系统之su命令的基本使用
|
13天前
|
监控 数据可视化 Java
调试技巧 - 用Linux命令排查Java问题
总的来说,使用Linux命令来排查Java问题,需要一定的实践经验和理论知识。然而,只要我们愿意花时间深入了解这些工具,我们就能够熟练地使用它们来分析和解决问题。此外,这些工具只是帮助我们定位问题,真正解决问题需要我们对Java和JVM有深入的理解,并能够读懂和分析代码。
48 13
|
25天前
|
监控 Linux
Linux基础:文件和目录类命令分析。
总的来说,这些基础命令,像是Linux中藏匿的小矮人,每一次我们使用他们,他们就把我们的指令准确的传递给Linux,让我们的指令变为现实。所以,现在就开始你的Linux之旅,挥动你的命令之剑,探索这个充满神秘而又奇妙的世界吧!
70 19
|
1月前
|
Linux
Linux 常用文件查看命令
`cat` 命令用于连接文件并打印到标准输出,适用于快速查看和合并文本文件内容。常用示例包括:`cat file1.txt` 查看单个文件,`cat file1.txt file2.txt` 合并多个文件,`cat &gt; filename` 创建新文件,`cat &gt;&gt; filename` 追加内容。`more` 和 `less` 命令用于分页查看文件,`tail` 命令则用于查看文件末尾内容,支持实时追踪日志更新,如 `tail -f file.log`。
62 5
Linux 常用文件查看命令
|
22天前
|
Linux
linux常用命令详细说明以及案例
本文介绍了Linux中几个常用的命令及其用法,包括:`ls`(列出目录内容)、`cd`(切换目录)、`mkdir`(创建目录)、`rm -p`(删除目录及内容)和`mv`(移动或重命名文件/目录)。每个命令都配有详细说明、语法格式、常见选项及实用案例,帮助用户更好地理解和使用这些基础命令。内容源自[linux常用命令详细说明以及案例](https://linux.ciilii.com/show/news-285.html)。
|
1月前
|
Linux
Linux od命令
本文详细介绍了Linux中的 `od`命令,包括其基本语法、常用选项和示例。通过这些内容,你可以灵活地使用 `od`命令查看文件内容,提高分析和调试效率。确保理解每一个选项和示例的实现细节,应用到实际工作中时能有效地处理各种文件查看需求。
69 19
|
2月前
|
缓存 Ubuntu Linux
Linux中yum、rpm、apt-get、wget的区别,yum、rpm、apt-get常用命令,CentOS、Ubuntu中安装wget
通过本文,我们详细了解了 `yum`、`rpm`、`apt-get`和 `wget`的区别、常用命令以及在CentOS和Ubuntu中安装 `wget`的方法。`yum`和 `apt-get`是高层次的包管理器,分别用于RPM系和Debian系发行版,能够自动解决依赖问题;而 `rpm`是低层次的包管理工具,适合处理单个包;`wget`则是一个功能强大的下载工具,适用于各种下载任务。在实际使用中,根据系统类型和任务需求选择合适的工具,可以大大提高工作效率和系统管理的便利性。
235 25
|
2月前
|
缓存 Linux
Linux查看内存命令
1. free free命令是最常用的查看内存使用情况的命令。它显示系统的总内存、已使用内存、空闲内存和交换内存的总量。 free -h • -h 选项:以易读的格式(如GB、MB)显示内存大小。 输出示例: total used free shared buff/cache available Mem: 15Gi 4.7Gi 4.1Gi 288Mi 6.6Gi 9.9Gi Swap: 2.0Gi 0B 2.0Gi • to
85 2