实验目的:
熟悉交换机的基本配置
,
学会在交换机上划分
VLAN
及如何将接口划分到指定的
VLAN.
本实验主要是用模拟器
DynamipsGUI
及
3640
的
IOS
文件做的实验
,
所以配置的命令有些会有出入
.
实验设备
:3640
交换机系列
实验内容:
其实交换机的基本操作包括设置特权登陆密码
,
设置控制台的密码等都跟路由器几乎一样的
.
在这里就不详说了
.
主要是讲一下如何划分
VLAN,
为后面的实验打下基础
.
首先在交换机上划分出
VLAN
sw#vlan database
sw(vlan)#vlan 10 name A
VLAN 10 added:
Name: A
sw(vlan)#vlan 20 name B
VLAN 20 added:
Name: B
sw(vlan)#vlan 30 name C
VLAN 30 added:
Name: C
sw(vlan)#vlan 40 name D
VLAN 40 added:
Name: D
sw(vlan)#vlan 50 name E
VLAN 50 added:
Name: E
sw(vlan)#exit (
注意这里一定要用
exit
来退出
,
交换机才会自动保存配置
)
APPLY completed.
Exiting....
sw#show vlan?
vlan-switch vlans (
这里比较郁闷
,
用模拟器做实验没办法
,
只能用这两个命令查看
VLAN
的配置了
)
sw#show version
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-JSX-M), Version 12.3(20), RELEASE SOFTWARE (fc2)
Technical Support: [url]http://www.cisco.com/techsupport[/url]
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Tue 08-Aug-06 16:37 by kesnyder
Image text-base: 0x60008B00, data-base: 0x61FAA000
ROM: ROMMON Emulation Microcode
ROM: 3600 Software (C3640-JSX-M), Version 12.3(20), RELEASE SOFTWARE (fc2)
sw uptime is 7 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19
System image file is "tftp://255.255.255.255/unknown"
cisco 3640 (R4700) processor (revision 0xFF) with 91136K/7168K bytes of memory.
Processor board ID 00000000
R4700 CPU at 100MHz, Implementation 33, Rev 1.2
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
32 FastEthernet/IEEE 802.3 interface(s)
DRAM configuration is 64 bits wide with parity enabled.
125K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
只能勉强凑合着做了
.
sw#show vlans
No Virtual LANs configured.
这个命令有点不懂
?
没有虚拟的
LAN
配置
?
在其它的交换机可能不会显示这样的结果
.
sw#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/1, Fa0/2, Fa0/3
Fa0/4, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa1/0, Fa1/1, Fa1/2, Fa1/3
Fa1/4, Fa1/5, Fa1/6, Fa1/7
Fa1/8, Fa1/9, Fa1/10, Fa1/11
Fa1/12, Fa1/13, Fa1/14, Fa1/15
10
A
active
20 B active
30
C
active
40 D active
50 E active
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 1002 1003
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
40 enet 100040 1500 - - - - - 0 0
50 enet 100050 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 1 1003
1003 tr 101003 1500 1005 0 - - srb 1 1002
1004 fdnet 101004 1500 - - 1 ibm - 0 0
1005 trnet 101005 1500 - - 1 ibm - 0 0
可以看到已经建立的
VLAN
A
、B、C、D、
E
了
.
好了
,
下面看下怎样将接口划分到指定的
VLAN
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
sw(config)#interface fa0/1
sw(config-if)#switchport access vlan 10
sw(config-if)#no shut (
将接口
Fa0/1
划分到
VLAN 10,
记得加上
no shut!)
其它的同样处理即可
sw(config)#int fa0/2
sw(config-if)#switchport access vlan 20
sw(config-if)#no shut
sw(config-if)#int fa0/3
sw(config-if)#switchport access vlan 30
sw(config-if)#no shut
sw(config-if)#int fa0/4
sw(config-if)#switchport access vlan 40
sw(config-if)#no shut
sw(config-if)#int fa0/5
sw(config-if)#switchport access vlan 50
sw(config-if)#no shut
sw#show vlans
No Virtual LANs configured.
sw#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa1/0
Fa1/1, Fa1/2, Fa1/3, Fa1/4
Fa1/5, Fa1/6, Fa1/7, Fa1/8
Fa1/9, Fa1/10, Fa1/11, Fa1/12
Fa1/13, Fa1/14, Fa1/15
10
A
active Fa0/1
20 B active Fa0/2
30
C
active Fa0/3
40 D active Fa0/4
50 E active Fa0/5
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 1002 1003
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0
40 enet 100040 1500 - - - - - 0 0
50 enet 100050 1500 - - - - - 0 0
1002 fddi 101002 1500 - - - - - 1 1003
1003 tr 101003 1500 1005 0 - - srb 1 1002
1004 fdnet 101004 1500 - - 1 ibm - 0 0
1005 trnet 101005 1500 - - 1 ibm - 0 0
我们可以看到
,
已经将接口划分到指定的
VLAN
了
.
接下来要配置的是给
VLAN
配置
IP
地址及默认网关
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
sw(config)#int vlan 10
sw(config-if)#ip address 192.168.1.2 255.255.255.0
sw(config-if)#ip default-gateway 192.168.1.1
sw(config)#exit
应该是配置成功的了
,
只是在这里没相应的命令查看得到
.
记住一下就可以了
.
简单的交换机配置就说到这里了
.
也许你们会觉得太简单
,
这里才刚刚开始
,
交换机是相当复杂的设备
,
它不像路由器用
IOS
去配置
,
而是用集成电路板去工作的
.
后面学的东西多了就会知道交换机的配置没想象中的简单
.
本文转自 独钩寒江雪 51CTO博客，原文链接：http://blog.51cto.com/bennie/103013，如需转载请自行联系原作者
