1-NET UX1000-实战-配置-Lync Server 2010-集成
1. 实验目的
FXS Quick Start 1.1
Configuring a call for the UX1000 FXS
Use the following step to configure a UX 1000 FXS Port.
Lync 分机----呼叫---FXS分机
8288------6001
FXS分机----呼叫--- Lync 分机
6001----8288
2. 登录-UX1000
用户名:admin
密 码:admin
3. 验证UX版本
Verifying the UX Versions
Prerequisite! Check your software level.
Verify that your UX1000 is loaded with firmware (boot partition) 2.1.6k and software image 2.0.0v108 or better. Older versions of
firmware/software will cause the FXS card to not function.
To begin the configuration, verify your Boot and Application versions.
3.1. 选择-Settings
3.2. 选择-System-Software Management-Boot Partition
3.3. 选择-System-Software Management-Application Partitions
Warning! Upgrade the UXSBA first.
If the UX application image requires an upgrade, always upgrade the UX Communication Service software (UXSBA) before upgrading
the UX application software. The firmware (boot) image can be upgraded either before or after the UX application software.
3.4. 验证-许可证
Verify Licensing
The system must have the FXS and DSP licenses to make calls. Depending upon the types of calls, the Transcoding license may also be necessary.
Unlimited---无限
SIP Registrations---注册普通的SIP话机
支持注册Skype
4. 验证-FXS卡/端口状态
Verify the FXS Card/Port State
Check to ensure that the FXS card and ports are functional by checking the System Tab | Overview Tab. The FXS Telco modules should show Activated, and the Service and Admin States should be UP.
Main Board:主板
FXS Not Activated and Up?
Did you upgrade the firmware and software?
5. 配置-UX1000 For FXS
Configuring the UX1000 for FXS
5.1. 增加-配置文件
Begin the configuration by adding a CAS Signaling Profile for FXS.
选择-Add FXS
选择-OK
首先得建立配置文件。
FXS Profile---S口的配置文件。
5.2. 增加-默认路由表
增加
Default Route Table
5.3. 增加-信令组
add a CAS Signaling Group
ISDN SG:---数字线路-信令组
SIP SG:-----IP-信令组---连接Lync Server 2010
CAS SG:----针对模拟线路，S口和O口
选择-Add CAS SG
Make sure to set the Channel Hunting to Own Number, otherwise the first free channel will answer every call (regardless of any other configuration settings).
参照:
Description:FXS Port 1
Channel Hunting:Own Number
Call Routing Table:Default Route Table
选择-OK
5.4. 分配号到-S口
Add an Assigned Channel and apply the desired phone number to the corresponding FXS port.
增加
Apply
The FXS-attached phone should now have dial-tone.
No dial-tone?
Are you certain your firmware and software are updated as noted at the beginning of these instructions?
5.5. 增加-一个FXS口呼叫的交换
Lync > FXS
FXS > PSTN
5.6. Lync 服务器
SIP
Add
Signaling Groups
5.7. 路由表
注意---更正---Lync > FXS
注意转换规则:
Lync > FXS
应用
应用
5.8. 测试
Lync---FXS
8288---6001
FXS---Lync
6001---8288
![clip_image003[1]](http://dynamic.blog.51cto.com/attachment/201201/22/711418_1327217882DqkJ.png "clip_image003[1]")
![clip_image004[1]](http://dynamic.blog.51cto.com/attachment/201201/22/711418_13272178838OC0.png "clip_image004[1]")
5.9.
6. 安装-jre-6u30-windows-i586-s.exe
7. 监控-通话
访问-NET UX1000
admin
admin
R是S口那边没挂断，正常挂断后不是这个样子。是绿色。
8. 安装-NET LX 2.8
NET LX 2.8---日志管理
9. UX1000-设置
10. 日志管理
10.1.打开-管理平台
10.2.选择-Syslog Server
10.3.选择-Start Listering
10.4.Lync分机---呼叫---FXS口
8288---》---6001
![clip_image001[1]](http://dynamic.blog.51cto.com/attachment/201201/22/711418_1327217988iWJY.png "clip_image001[1]")
10.5.接听
![clip_image002[1]](http://dynamic.blog.51cto.com/attachment/201201/22/711418_1327217993YMip.png "clip_image002[1]")
10.6.选择-Stop Listering
10.7.选择-分析
10.8.
11. Lync分机---呼叫---FXS口分机
11.1.SIP
SIP Server Tables
填写:
Lync Server 2010-服务器
192.168.1.82 5068
SIP Options
11.2.CAS
新建-FXS---分机配置文件
FXS Profile
11.3.Signaling Groups
信令组
CAS SG CAS信令组
写入FXS口---分机号
SIP SG SIP信令组
写入 SIP服务器
FX0---也需要建信令组.需实战
E1----也需要建信令组.需实战
11.4.Transformation
转换规则
11.5.Call Routing Table
