#!/bin/bash
# ultimate.sh for duron
# Based on Wonder Shaper v1.1a
echo "/usr/sbin/ultimate.sh: "
# Please read the README before filling out these values.
# Set the following values to somewhat less than your actual download
# and upload speed in kilobits. Also set the device that is to be shaped.
# Run a speed test from netspeed.stanford.edu with no shaping enabled.
# Multiply the reported rates in Kb/s by ~.95 and enter them here:
# Example: DNLINK=4.76M*.95 = 4522
# UPLINK=444.26K*.95 = 422
# Run the stanford test again. Note: stanford uses high ports.
# Tweak during heavy upload so that each affected class has a small backlog but
# as few dropped packets as possible. Interactive must NEVER backlog!
# If heavy downloads affect uploads, tweak IMQ so there is a small backlog but
# as few dropped packets as possible.
# Watch the logs for "some class has too small rate" even with quantum set.
# Stanford is in class 30; egress rate 36% ceil 92%, ingress rate 57% ceil 92%
# Download w/HTB is plenty (5.2x), don't tweak.
# Upload w/UPLINK=470 -> range 416 - 420 = ~85% of uCEIL. Try for 90% - 91%.
dCEIL=9740 # Stanford max down with no shaping (best of 3 tests)
DNLINK=9350 # (.95*dCEIL, rounded down)
uCEIL=974 # Stanford max up (best of 3 tests).
UPLINK=952 # Tweak. (was 470=.95*uCEIL, rounded up)
# Percentages, egress:
# sum(Ie + Ae + Be + Pe) _MUST_ = 100
Ie=7 # Interactive
Ae=50 # Accelerated
Be=36 # Bulk
Pe=7 # Penalized
# Percentages, ingress (IMQ):
# sum(Ii + Ai + Bi) _MUST_ = 100
Ii=5 # Interactive
Ai=38 # Accelerated
Bi=57 # Bulk
IFE=eth1 # Egress NIC; External Interface
IMQ=imq0 # Egress NIC - shape incoming
# Local IPs:
ATJ=`cat /etc/firewall/Duron`
# Remote IPs:
#ADE="216.196.97.0/24" # adelphia.net
CHS="" # chsoft.biz
DMF="" # Diana's
NGUY="74.209.0.80/28" # Newsguy
#HBED1="62.146.66.160/27" # H+BEDV (antivirus)
#HBED2="217.11.60.0/27" # H+BEDV (antivirus)
#ISW1="207.178.128.0/24" # iswest
#ISW2="216.166.71.0/24" # iswest
#ISW3="216.196.105.0/24" # iswest (giganews)
LHD1="" # L. H. Dottie
LHD2="" # L. H. Dottie
#NEWS="" # news.chsoft.biz
NSAD="67.21.15.0/24" # Adelphia dns servers
NSTW="66.75.164.0/24" # Time Warner dns servers
#QUE1="63.231.95.0/24" # quest
#QUE2="207.225.159.0/24" # quest
SC=`cat /etc/firewall/SupportJ` # Note that ports 5500 and 5900 have priority
#TERA="66.150.105.0/24" # teranews
WALK="" # Walker Foods
#YIC="" # yesican.chsoft.biz
###### EXPLANATION
# See 'INGRESS' below for information about incoming packets. All of this
# except for that refers to queueing outgoing packets.
#
# Most of what is sent goes out on a randomly selected high SOURCE port
# ('sport') to a specific DESTINATION port ('dport'). For example, an http
# request is sent with 'dport' = 80 and 'sport' = random. Therefore, 'sport'
# specifications are rarely applicable. The port number is located in the
# packet header and is specified thus:
# "u32 match ip dport PORT# 0xffff" or "u32 match ip sport PORT# 0xffff"
#
# Since shaping means quequeing OUTGOING packets, your IP Address(es) are
# SOURCEs ('src') and the remote machine's IP Address(es) are DESTINATIONs
# ('dst') - so, as with 'sport', 'src' specifications are rarely applicable.
# The IP Address is located in the packet header and is specified thus:
# "u32 match ip src IP-ADDRESS" or "u32 match ip dst IP-ADDRESS"
#
# Read the HOWTO "All the filtering commands you will normally need" for
# protocol information (TCP, UDP, ICMP, GRE, IPSEC). Also see the TOS and
# ICMP sections below.
######
# Sometimes you may notice low priority OUTGOING traffic slowing down important
# traffic. In that case, the following eLoPrio options may help you:
## * * * * Structure:
## {1} * * * * * IFE DEFINITIONS
## {2} * * * * * EGRESS on IFE (HERE --> INTERNET)
## {3} * * * * * IMQ INGRESS shaping on IFE (HERE <-- INTERNET)
###### {1} External Interface DEFINITIONS:
# Ports:
# eLoPrioSPORT ('sport')
# Set this to source ports that should have low priority. If you have
# an unimportant webserver on your traffic, set this to 80.
# These go into class 40
# (some ports ) 20 21 22 23 25 53 80 113 119 873
# (and what they are:) FTPd FTPc SSH SMTP DNS HTTP IDENT NNTP Rsync
# 9001 is tor Server, 9030 is tor Directory
# Search 6881 for torrent special handling (1:40)
# Matches FROM me:PORT
eLoPrioSPORT="8 21 23 67 68 79 110 135 137 138 139 389 445 446 901 1026 1027 1028 1029 1234 5018"
# eHiPrioSPORT ('sport')
# These go into class 20. SSH and scp are interactive (class 10).
# *** Make sure no eLoPrioSPORTs are duplicated here! ***
# Matches (apparently) nothing.
eHiPrioSPORT="113 119 123 443 563 873 5500 5900"
# eLoPrioDPORT ('dport')
# Set this to destination ports that should have low priority.
# The following are from my TARPIT list: 79 135 137 138 139 445 901
# Matches DIR=FROM? remote:PORT
# These go into class 40
eLoPrioDPORT="8 21 23 67 68 79 110 135 137 138 139 389 445 446 901 1026 1027 1028 1029 1234 5018"
# eHiPrioDPORT ('dport')
# *** Make sure no eLoPrioDPORTs are duplicated here! *** ssh is interactive.
# Matches DIR=FROM? ?:PORT
# These go into class 20
eHiPrioDPORT="113 119 123 443 563 873 5500 5900"
# IPs / Netmasks:
# Set this to hosts or netmasks in your network that should have low priority.
# Low priority OUTGOING traffic. You can leave this blank if you want.
# Matches TO REMOTE
# These go into class 40
eLoPrioCIDR_Src=""
#eLoPrioCIDR_Src="$ATJ"
# See EXPLANATION above; these do not need to be here.
# Matches (apparently) nothing.
# These go into class 20
eHiPrioCIDR_Src="$CHS $LHD1 $NGUY $SC $WALK"
# Set this to hosts or netmasks on the internet that should have low priority.
# Matches FROM REMOTE
# These go into class 40
eLoPrioCIDR_Dst="221.0.0.0/8"
# high priority destination netmasks ('dst'):
# Matches DIR? REMOTE:IP
# These go into class 20
eHiPrioCIDR_Dst="$CHS $LHD1 $NGUY $SC $WALK"
###### End External Interface DEFINITIONS
if [ "$1" = "status" ]; then
echo "Sent on $IFE:"
# tc -s filter show dev $IFE
tc -d qdisc ls dev $IFE
tc -s qdisc ls dev $IFE
tc -s class ls dev $IFE
echo "'rate #bit' means Bytes per Second"
echo "Received on $IMQ:"
# tc -s filter show dev $IMQ
tc -d qdisc ls dev $IMQ
tc -s qdisc ls dev $IMQ
tc -s class ls dev $IMQ
echo "'rate #bit' is meaningless. Measure by Backlog and Dropped."
exit
fi
# Clean existing setup, hiding errors
tc qdisc del dev $IFE root 2> /dev/null > /dev/null
tc qdisc del dev $IFE ingress 2> /dev/null > /dev/null
iptables -t mangle -D PREROUTING -i $IFE -j IMQ --todev 0 2>/dev/null > /dev/null
tc qdisc del dev $IMQ root 2> /dev/null > /dev/null
ip link set $IMQ down 2> /dev/null > /dev/null
modprobe -r ipt_IMQ # iptables
modprobe -r imq # device
modprobe -r cls_u32
modprobe -r sch_esfq # requires modified tc
modprobe -r sch_sfq
modprobe -r sch_htb
modprobe -r sch_ingress
if [ "$1" = "stop" ]; then
exit
fi
###### {2} uplink (EGRESS) on IFE
# This part shapes on the external interface: (HERE --> INTERNET)
# Install root HTB, point default traffic to 1:30:
tc qdisc add dev $IFE root handle 1: htb default 30
# Shape everything at $UPLINK speed - this prevents huge queues in your
# DSL modem which destroy latency:
tc class add dev $IFE parent 1: classid 1:1 htb rate ${uCEIL}kbit burst 32k cburst 20k
# High prio (interactive) class 1:10:
tc class add dev $IFE parent 1:1 classid 1:10 htb rate $[Ie*$UPLINK/100]kbit \
ceil ${uCEIL}kbit burst 32k cburst 20k quantum 1514 prio 1
# Accelerated class 1:20 - the HIPRIO stuff:
tc class add dev $IFE parent 1:1 classid 1:20 htb rate $[Ae*$UPLINK/100]kbit \
ceil $[96*$uCEIL/100]kbit burst 16k cburst 10k quantum 1514 prio 2
# Bulk & default class 1:30 - gets a low priority:
tc class add dev $IFE parent 1:1 classid 1:30 htb rate $[Be*$UPLINK/100]kbit \
ceil $[92*$UPLINK/100]kbit burst 8k cburst 5k quantum 1514 prio 3
# ceil $[Ae*$UPLINK/100]kbit burst 8k cburst 5k quantum 1514 prio 3
# Penalized class 1:40 - the LOPRIO stuff gets the lowest rate and priority:
tc class add dev $IFE parent 1:1 classid 1:40 htb rate $[Pe*$UPLINK/100]kbit \
ceil $[80*$UPLINK/100]kbit burst 2k quantum 1514 prio 4
# ceil $[Be*$UPLINK/100]kbit burst 2k quantum 1514 prio 4
# Some get Stochastic Fairness:
# LARTC mailing list indicates that interactive should not be included. Andy
# Furniss suggests that bulk be the only thing subject to SF. I set a long
# perturb for accelerated and exclude interactive.
# Increased limit from 64 to reduce # of dropped packets 7Dec07
# 11Dec07: esfq limit must be less than or equal depth; depth max = 1024:
#tc qdisc add dev $IFE parent 1:10 handle 10: esfq limit 64 depth 64 divisor 10 hash classic perturb 20
tc qdisc add dev $IFE parent 1:20 handle 20: esfq limit 256 depth 256 divisor 10 hash classic perturb 99
tc qdisc add dev $IFE parent 1:30 handle 30: esfq limit 1024 depth 1024 divisor 10 hash classic perturb 20
tc qdisc add dev $IFE parent 1:40 handle 40: esfq limit 32 depth 32 divisor 10 hash classic perturb 10
# ARP:
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match u16 0x0806 0xffff at -2 flowid 1:40
###### Accelerate (interactive) the following:
# To speed up downloads while an upload is going on, put ACK packets in
# the interactive class 1:10:
# IP header length 0x5 (32 bit words)
# IP total length 0x34 (ACK + 12 bytes of TCP options)
# TCP ACK set (bit 5, offset 33)
# ("at nexthdr+33" = "at 13")
## Match ACK on all TCP packets with the ACK bit set:
## Caveat!: This can match packets up to 64K; don't do it. Match small.
#tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
# match ip protocol 6 0xff \
# match u8 0x10 0xff at nexthdr+13 \
# flowid 1:10
# Match TCP packets smaller than 128 bytes:
# Because of the mask, can only match powers of 2 (32, 64, 128...)
# 0xfff8 - 8
# 0xfff0 - 16
# 0xffe0 - 32
# 0xffc0 - 64
# 0xff80 - 128
# Remarked out ACK, normally 5th line: match u8 0x10 0xff at 33 \
# "match u8 0x05 0x0f at 0" makes sure the IP header is 20 bytes.
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip protocol 6 0xff \
match u8 0x05 0x0f at 0 \
match u16 0x0000 0xff80 at 2 \
flowid 1:10
# SSH and scp are interactive.
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip dport 22 0xffff flowid 1:10
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip sport 22 0xffff flowid 1:10
# dns is interactive:
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip dport 53 0xffff flowid 1:10
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip sport 53 0xffff flowid 1:10
###### Some traffic is preferred, so in our class 1:20:
for a in $eHiPrioDPORT; do
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip dport $a 0xffff flowid 1:20
done
for a in $eHiPrioSPORT; do
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip sport $a 0xffff flowid 1:20
done
for a in $eHiPrioCIDR_Src; do
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip src $a flowid 1:20
done
for a in $eHiPrioCIDR_Dst; do
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip dst $a flowid 1:20
done
###### Give these short shrift:
# Penalized traffic suffers a worse fate in our slowest class 1:40:
# Special for torrents ports 6880-6887:
# The mask determines the number of ports: ffff=1 fffe=2 fffc=4 fff8=8 fff0=16
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip dport 6881 0xfff8 flowid 1:40
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip sport 6881 0xfff8 flowid 1:40
for a in $eLoPrioDPORT; do
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip dport $a 0xffff flowid 1:40
done
for a in $eLoPrioSPORT; do
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip sport $a 0xffff flowid 1:40
done
for a in $eLoPrioCIDR_Src; do
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip src $a flowid 1:40
done
for a in $eLoPrioCIDR_Dst; do
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip dst $a flowid 1:40
done
if [ -f /etc/firewall/shitlist ]; then
while read SLIST; do
SLIST=$(echo "$SLIST" | awk '{print $1}')
tc filter add dev $IFE parent 1: protocol all prio 5 u32 \
match ip dst $SLIST flowid 1:40
done
本文转自feisky博客园博客，原文链接：http://www.cnblogs.com/feisky/archive/2011/11/20/2256590.html，如需转载请自行联系原作者
