1. 前言

本例演示了采用CH307串口3与Arduino软串口收发通信，熟悉STM32和Arduino开发用易上手配置。✨✨✨

这是使用MounRiver Studio开发的项目，支持在RISC-V核心基础硬件CH32V307评估板上使用带有msh Shell的RTOS快速原型。

MCU：CH32V307VCT6，主频 144MHz，FLASH和RAM可配置

l 全双工或半双工的同步或异步通信

l NRZ 数据格式

l 分数波特率发生器，最高 9Mbps

l 可编程数据长度

l 可配置的停止位

l 支持 LIN，IrDA 编码器，智能卡

l 支持 DMA

l 多种中断源

首先，应安装 CH32V307 评估板的驱动程序，打开设备管理器查看USB 端口和外部接口已准备就绪。

2. 软件配置

2.1 安装MounRiver Studio

环境搭建教程：https://blog.csdn.net/VOR234/article/details/128932474

3. UASRT项目测试

3.1 打开UASRT工程

评估板说明及参考例程：https://www.wch.cn/downloads/CH32V307EVT_ZIP.html

进入EXAM目录，就有对应的外设教程

进入USART_HalfDuplex文件下，双击USART_HalfDuplex.wvproj,

打开项目工程如下，main.c在user文件夹下

3.2 CH307串口发送数据到Arduino实验

修改CH307的main.c，杜邦线连接PB10(TX)--D2(RX);PB11(RX)--D3(TX)

/********************************** (C) COPYRIGHT *******************************
* File Name          : main.c
* Author             : WCH
* Version            : V1.0.0
* Date               : 2021/06/06
* Description        : Main program body.
*********************************************************************************
* Copyright (c) 2021 Nanjing Qinheng Microelectronics Co., Ltd.
* Attention: This software (modified or not) and binary are used for 
* microcontroller manufactured by Nanjing Qinheng Microelectronics.
*******************************************************************************/
/*
 *@Note:采用CH307串口3与Arduino软串口收发通信
Hardware connection:PB10(TX)--D2(RX);PB11(RX)--D3(TX)
*/
#include "debug.h"
/* Global typedef */
typedef enum
{
    FAILED = 0,
    PASSED = !FAILED
} TestStatus;
/* Global define */
//#define RxSize1    (size(RxBuffer1))
#define TxSize1    (size(TxBuffer1))
#define RxSize1    256
#define size(a)    (sizeof(a) / sizeof(*(a)))
/* Global Variable */
u8 TxBuffer1[] = "abcd"; /* Send by UART3 */
u8 RxBuffer1[RxSize1] = {0};                                                   /* USART3 Using  */
u8 TxCnt1 = 0, RxCnt1 = 0;
/*********************************************************************
 * @fn      USARTx_CFG
 *
 * @brief   Initializes the USART3 peripheral.
 *
 * @return  none
 */
void USARTx_CFG(void)
{
    GPIO_InitTypeDef  GPIO_InitStructure = {0};
    USART_InitTypeDef USART_InitStructure = {0};
//    NVIC_InitTypeDef NVIC_InitStructure = { 0 };
    RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);
    /* USART3 TX-->B.10  RX-->B.11 */
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11; /* Only Configure TX Pin */
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
    GPIO_Init(GPIOB, &GPIO_InitStructure);
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10; /* Only Configure TX Pin */
    GPIO_Init(GPIOB, &GPIO_InitStructure);
    USART_InitStructure.USART_BaudRate = 9600;
    USART_InitStructure.USART_WordLength = USART_WordLength_8b;
    USART_InitStructure.USART_StopBits = USART_StopBits_1;
    USART_InitStructure.USART_Parity = USART_Parity_No;
    USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
    USART_InitStructure.USART_Mode = USART_Mode_Tx | USART_Mode_Rx;
    USART_Init(USART3, &USART_InitStructure);
    USART_Cmd(USART3, ENABLE);
//    NVIC_InitStructure.NVIC_IRQChannel = USART3_IRQn;
//    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
//    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
//    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
//    NVIC_Init(&NVIC_InitStructure);
//
//    USART_Cmd(USART3, ENABLE);
}
/*********************************************************************
 * @fn      main
 *
 * @brief   Main program.
 *
 * @return  none
 */
int main(void)
{
    NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
    SystemCoreClockUpdate();
    Delay_Init();
    USART_Printf_Init(115200);  
    printf("SystemClk:%d\r\n", SystemCoreClock);
    printf( "ChipID:%08x\r\n", DBGMCU_GetCHIPID() );
    printf("USART3 Arduino TEST\r\n");
    USARTx_CFG(); /* USART3 INIT */
    printf("USART3 INIT\r\n");
    while(1)
    {
/*
CH307发送数据到Arduino
*/
        while(USART_GetFlagStatus(USART3, USART_FLAG_TXE) == RESET){
            }
        for ( int var = 0;  var < TxSize1-1; ++ var) {
            USART_SendData(USART3, TxBuffer1[var]);
            Delay_Ms(1);
        }
        printf("TxBuffer1:%s\r\n", TxBuffer1);
        Delay_Ms(1000);
    }
}

Arduino UNO 采用mixly编程

代码如下

#include <SoftwareSerial.h>
SoftwareSerial mySerial(2,3);
String item;
volatile int number;
void setup(){
  mySerial.begin(9600);
  Serial.begin(9600);
  item = "hello123456";
  number = 0;
  Serial.println(item);
  mySerial.println(item);
}
void loop(){
  if (mySerial.available() > 0) {
    item = mySerial.readString();
    Serial.println(String("item:") + String(item) + String("; number:") + String(number));
    number++;
  }
  delay(1);
}

实验效果

3.3 CH307串口接收数据Arduino实验

接线保持不变

修改CH307的main.c，杜邦线连接PB10(TX)--D2(RX);PB11(RX)--D3(TX)

/********************************** (C) COPYRIGHT *******************************
* File Name          : main.c
* Author             : WCH
* Version            : V1.0.0
* Date               : 2021/06/06
* Description        : Main program body.
*********************************************************************************
* Copyright (c) 2021 Nanjing Qinheng Microelectronics Co., Ltd.
* Attention: This software (modified or not) and binary are used for 
* microcontroller manufactured by Nanjing Qinheng Microelectronics.
*******************************************************************************/
/*
 *@Note:采用CH307串口3与Arduino软串口收发通信
Hardware connection:PB10(TX)--D2(RX);PB11(RX)--D3(TX)
*/
#include "debug.h"
/* Global typedef */
typedef enum
{
    FAILED = 0,
    PASSED = !FAILED
} TestStatus;
/* Global define */
//#define RxSize1    (size(RxBuffer1))
#define TxSize1    (size(TxBuffer1))
#define RxSize1    256
#define size(a)    (sizeof(a) / sizeof(*(a)))
/* Global Variable */
u8 TxBuffer1[] = "abcd"; /* Send by UART3 */
u8 RxBuffer1[RxSize1] = {0};                                                   /* USART3 Using  */
u8 TxCnt1 = 0, RxCnt1 = 0;
/*********************************************************************
 * @fn      USARTx_CFG
 *
 * @brief   Initializes the USART3 peripheral.
 *
 * @return  none
 */
void USARTx_CFG(void)
{
    GPIO_InitTypeDef  GPIO_InitStructure = {0};
    USART_InitTypeDef USART_InitStructure = {0};
//    NVIC_InitTypeDef NVIC_InitStructure = { 0 };
    RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);
    /* USART3 TX-->B.10  RX-->B.11 */
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11; /* Only Configure TX Pin */
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
    GPIO_Init(GPIOB, &GPIO_InitStructure);
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10; /* Only Configure TX Pin */
    GPIO_Init(GPIOB, &GPIO_InitStructure);
    USART_InitStructure.USART_BaudRate = 9600;
    USART_InitStructure.USART_WordLength = USART_WordLength_8b;
    USART_InitStructure.USART_StopBits = USART_StopBits_1;
    USART_InitStructure.USART_Parity = USART_Parity_No;
    USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
    USART_InitStructure.USART_Mode = USART_Mode_Tx | USART_Mode_Rx;
    USART_Init(USART3, &USART_InitStructure);
    USART_Cmd(USART3, ENABLE);
//    NVIC_InitStructure.NVIC_IRQChannel = USART3_IRQn;
//    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
//    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
//    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
//    NVIC_Init(&NVIC_InitStructure);
//
//    USART_Cmd(USART3, ENABLE);
}
/*********************************************************************
 * @fn      main
 *
 * @brief   Main program.
 *
 * @return  none
 */
int main(void)
{
    NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
    SystemCoreClockUpdate();
    Delay_Init();
    USART_Printf_Init(115200);  
    printf("SystemClk:%d\r\n", SystemCoreClock);
    printf( "ChipID:%08x\r\n", DBGMCU_GetCHIPID() );
    printf("USART3 Arduino TEST\r\n");
    USARTx_CFG(); /* USART3 INIT */
    printf("USART3 INIT\r\n");
    while(1)
    {
/*
CH307发送数据到Arduino
*/
//        while(USART_GetFlagStatus(USART3, USART_FLAG_TXE) == RESET){
//            }
//        for ( int var = 0;  var < TxSize1-1; ++ var) {
//            USART_SendData(USART3, TxBuffer1[var]);
//            Delay_Ms(1);
//        }
//        printf("TxBuffer1:%s\r\n", TxBuffer1);
//        Delay_Ms(1000);
/*
从Arduino接收数据到CH307
 */
        RxBuffer1[RxCnt1++] = USART_ReceiveData(USART3);
        while(RxBuffer1[RxCnt1-1] == 'i'|| RxCnt1-1 != 0)
        {
            while(USART_GetFlagStatus(USART3, USART_FLAG_RXNE) == RESET){
            }
            RxBuffer1[RxCnt1++] = USART_ReceiveData(USART3);
            if (RxBuffer1[RxCnt1-1] == '\t') {
                printf("RxBuffer1:%s\r\n", RxBuffer1);
                break;
            }
        }
        RxCnt1 = 0;
        for (int var = 0; var < RxSize1; ++var) {
            RxBuffer1[var] = 0;
        }
        Delay_Ms(1);
    }
}

Arduino UNO 采用mixly编程

代码如下

#include <SoftwareSerial.h>
SoftwareSerial mySerial(2,3);
String item;
volatile int number;
void setup(){
  mySerial.begin(9600);
  Serial.begin(9600);
  item = "hello123456";
  number = 0;
  Serial.println(item);
  mySerial.println(item);
}
void loop(){
  mySerial.print(String("item:") + String(item) + String("; number:") + String(number) + String("; number:") + String(number) + String("\t"));
  number++;
  delay(1);
}

实验效果

4. 小结

🥳🥳🥳通过对这篇文章我们掌握了沁恒WCH CH32V307V-R1与Arduino的串口通讯，尝试与Arduino通讯做更加好玩的实验，进而丰富我们的生活。🛹🛹🛹从而实现对外部世界进行感知，充分认识这个有机与无机的环境，🥳🥳🥳科学地合理地进行创作和发挥效益，然后为人类社会发展贡献一点微薄之力。🤣🤣🤣

【沁恒WCH CH32V307V-R1与Arduino的串口通讯】

1. 前言

2. 软件配置

2.1 安装MounRiver Studio

3. UASRT项目测试

3.1 打开UASRT工程

3.2 CH307串口发送数据到Arduino实验

3.3 CH307串口接收数据Arduino实验

4. 小结

热门文章

最新文章

相关课程

相关电子书

推荐镜像

热门

活动广场

任务中心

开发者评测

高校计划

乘风者计划

训练营

阿里云MVP

话题

直播

下载

镜像站

技术资料

插件

【沁恒WCH CH32V307V-R1与Arduino的串口通讯】

1. 前言

2. 软件配置

2.1 安装MounRiver Studio

3. UASRT项目测试

3.1 打开UASRT工程

3.2 CH307串口发送数据到Arduino实验

3.3 CH307串口接收数据Arduino实验

4. 小结

热门文章

最新文章

相关课程

相关电子书

推荐镜像